|
Genuine Lindhaus PB12 powerhead.
RAISE YOUR EXPECTATIONS
- The PB series was designed to give a professional solution for the specific requirements of the customer.
- Lindhaus engineered this accessory like a machine, it is equipped with the most sophisticated technical features in the world.
- Today the central vac, the canister vacuum and the back pack, can be equipped with the PB units, for an extraordinary increase in cleaning efficiency.
ENGINEERED TO LAST
- Long service life and low vibration levels, are achieved with superior engineering and precision manufacturing. All rotating components are balanced and protected by electronic controls.
ELECTRONIC LOGIC
- Proven integrated circuits protect the motor and the transmission from overload and assist the operator in making the most efficient brush height setting.
DESIGN SUPERIORITY
- Rugged and efficient power brush picks up what others leave behind. Our maintenance free power brush has a three year warranty on the cogged drive belt. With non-marking rubber tires and an electrical switch position to stop the power brush motor, the transition to hard floor saves time and reduces airborne dust.
Looking for an extension wand to compliment your Lindhaus PB12 powerhead? Check out the Universal Stainless Steel Telescopic Wand.
100
|
Motor Cover, Light Gray |
101
|
Lens Set, Red and Green
|
102
|
Joint, Complete with Cord |
104
|
Joint Pin Slide |
105
|
Screw, 3.9x13 (Single)
|
106
|
Right Connector Support |
107
|
Plunger
|
108
|
Spring
|
109
|
Bushing
|
110
|
Screw, 2.9x16 (Single)
|
111
|
Slide
|
112
|
Foot Pedal, Dark Gray
|
113
|
Left Joint Support |
114
|
Switch Activator Pin
|
115
|
Spring Switch Activator Pin
|
116
|
Microswitch
|
117
|
Screw, 2.2x16 (Single)
|
118
|
Circuit Board M30 120V/180W
|
119
|
Exhaust Filter
|
120
|
Filter Brush Motor
|
121
|
Brush Motor R73/25V 120V/180W
|
122
|
Metal Spacer
|
123
|
Metal Pulley
|
124
|
Nut, Pinion
|
125
|
Screw, 3.9x16 (Single)
|
126
|
Timing Belt, 7mm
|
127
|
Transmission, Left Support with Bearings
|
128
|
Brush Pulley with Metal Insert
|
130
|
Brush Shaft, M30 (12") |
131
|
Brush Roller M30 (12"), 2 Bristle |
132
|
Right Brush Support with Bearings |
133
|
Brush Shoe Plate M30 (12") |
134
|
Screw M6x9
|
135
|
Star Washer
|
136
|
Base Housing M30 (12"), Light Gray |
137
|
Bumper M30 (12"), Dark Gray |
138
|
Front Axle
|
139
|
Front Wheel Rubber
|
140
|
Spring
|
141
|
Spring Stop Plate
|
142
|
Brush Height Adjuster
|
143
|
Adjusting Knob, Dark Gray
|
144
|
Rear Axle
|
145
|
Rear Big Wheel Rubber
|
146
|
Wheel Retainer Cap
|
147
|
Screw, 3.5x19 (Single)
|
150
|
Swivel Connector
|
151
|
Stopcord Bracket
|
152
|
Strain Relief
|
153
|
Screw, 2.9x16 (Single)
|
154
|
Power Cord, 45"
|
155
|
Screw, 2.9x9.5 (Single)
|
156
|
Cord Clamp
|
157
|
Terminal Block, 2 Poles
|
|
|
|
|
Looking for a specific part for your Lindhaus PB12 powerhead? Call us at (855) 649-7996 to place a special order!
|
|
|